 |
|
|
|
Reduced Shipping Cost Available
If your order is small electric or miscellaneous accessory items, and your total package weight is under 13oz, then we will send your order at reduced shipping cost whenever possible. And we will provide you partial refund for the difference you paid on the shopping cart at check out.
International Customers:
Please contact us for international shipping rates.
|
$15.99
|
ZTW 12A Brushless Speed Controller BEC 5V/1A
recommended esc for 2204 motors(Turnigy or T-motor) with 28" sbach or 34" 342Pro
* ZTW ESCs may require throttle calibration to be setup before use. Please see page 6 and 7 in the included user manual for instructions on "Powering up the ESC for the first time and setting the automatic throttle calibration."
Specifications:
Output :Continuous Current 12A ,Burst Current 16A for 10 seconds
Battery Cell :5-12NC/2-4Lipo
Weight :8g
BEC Output :5V/1A
Switching Frequency: 8kHz/16kHz
Size :21*22*4mm(L*W*H)
Features:
Extremely low internal resistance
Super smooth and accurate throttle linearity
Safety thermal over-load protection
Auto throttle shut down in signal lose situation
Supports high RPM motors
Power arming protection (prevents the motor from accidentally running when switched ON)
New Advanced programming software
Programmable Features:
1. Brake: ON/OFF
2. Battery type: LiPo or NiCad/NiMh
3. Low Voltage Protection Threshold (Cutoff Threshold)
4. Restore factory setup defaults
5. Timing Setup: Automatic/Low/High
6. Soft Acceleration Start ups: Very Soft / Soft Acceleration / Start Acceleration
7. Active RPM Control (Heli Governor mode)
8. Motor Rotation: Forward / Reverse
9. Switching Frequency: 8kHz/16kHz
10. Low Voltage Cutoff Type: Reduce Power / Hard cutoff |
$17.99
|
ZTW 20A Brushless Speed Controller BEC 5V/2A
recommended esc for gh micro jet v3 motor with nanoshark
* ZTW ESCs may require throttle calibration to be setup before use. Please see page 6 and 7 in the included user manual for instructions on "Powering up the ESC for the first time and setting the automatic throttle calibration."
Specifications:
Output :Continuous Current 20A ,Burst Current 30A for 10 seconds
Battery Cell :5-12NC/2-4Lipo
Weight :18g
BEC Output :5V/2A
Switching Frequency: 8kHz/16kHz
Size :28*28*8mm(L*W*H)
Features:
Extremely low internal resistance
Super smooth and accurate throttle linearity
Safety thermal over-load protection
Auto throttle shut down in signal lose situation
Supports high RPM motors
Power arming protection (prevents the motor from accidentally running when switched ON)
New Advanced programming software
Programmable Features:
1. Brake: ON/OFF
2. Battery type: LiPo or NiCad/NiMh
3. Low Voltage Protection Threshold (Cutoff Threshold)
4. Restore factory setup defaults
5. Timing Setup: Automatic/Low/High
6. Soft Acceleration Start ups: Very Soft / Soft Acceleration / Start Acceleration
7. Active RPM Control (Heli Governor mode)
8. Motor Rotation: Forward / Reverse
9. Switching Frequency: 8kHz/16kHz
10. Low Voltage Cutoff Type: Reduce Power / Hard cutoff
|
$22.99
|
ZTW 30A Brushless Speed Controller BEC 5V/3A
recommended esc for hxt 3000kv motor with babyshark
* ZTW ESCs may require throttle calibration to be setup before use. Please see page 6 and 7 in the included user manual for instructions on "Powering up the ESC for the first time and setting the automatic throttle calibration."
Specifications:
Output :Continuous Current 30A , Burst Current 40A for 10 seconds
Battery Cell :5-12NC/2-4Lipo
Weight :28g
BEC Output :5V/3A
Switching Frequency: 8kHz/16kHz
Size :28*40*8mm(L*W*H)
Features:
Extremely low internal resistance
Super smooth and accurate throttle linearity
Safety thermal over-load protection
Auto throttle shut down in signal lose situation
Supports high RPM motors
Power arming protection (prevents the motor from accidentally running when switched ON)
New Advanced programming software
Programmable Features:
1. Brake: ON/OFF
2. Battery type: LiPo or NiCad/NiMh
3. Low Voltage Protection Threshold (Cutoff Threshold)
4. Restore factory setup defaults
5. Timing Setup: Automatic/Low/High
6. Soft Acceleration Start ups: Very Soft / Soft Acceleration / Start Acceleration
7. Active RPM Control (Heli Governor mode)
8. Motor Rotation: Forward / Reverse
9. Switching Frequency: 8kHz/16kHz
10. Low Voltage Cutoff Type: Reduce Power / Hard cutoff |
$31.99
|
ZTW 40A Brushless Speed Controller SBEC 5.5V/4A
recommended esc for 4s setup, use with md 2900kv motor on balsa babyshark
* ZTW ESCs may require throttle calibration to be setup before use. Please see page 6 and 7 in the included user manual for instructions on "Powering up the ESC for the first time and setting the automatic throttle calibration."
Specifications:
Output :Continuous Current 40A ,Burst Current 60A for 10 seconds
Battery Cell :5-18NC/2-6Lipo
Weight :32g
BEC Output :5.5V/4A
Switching Frequency: 8kHz/16kHz
Size :23*52*7mm(L*W*H)
Features:
Extremely low internal resistance
Super smooth and accurate throttle linearity
Safety thermal over-load protection
Auto throttle shut down in signal lose situation
Supports high RPM motors
Power arming protection (prevents the motor from accidentally running when switched ON)
New Advanced programming software
Programmable Features:
1. Brake: ON/OFF
2. Battery type: LiPo or NiCad/NiMh
3. Low Voltage Protection Threshold (Cutoff Threshold)
4. Restore factory setup defaults
5. Timing Setup: Automatic/Low/High
6. Soft Acceleration Start ups: Very Soft / Soft Acceleration / Start Acceleration
7. Active RPM Control (Heli Governor mode)
8. Motor Rotation: Forward / Reverse
9. Switching Frequency: 8kHz/16kHz
10. Low Voltage Cutoff Type: Reduce Power / Hard cutoff |
$46.99
|
ZTW 60A Brushless Speed Controller SBEC 5.5V/4A
recommended esc for 3s setup, use with md 4200kv motor (velocity) on balsa babyshark
* ZTW ESCs may require throttle calibration to be setup before use. Please see page 6 and 7 in the included user manual for instructions on "Powering up the ESC for the first time and setting the automatic throttle calibration."
Specifications:
Output :Continuous Current 60A ,Burst Current 80A for 10 seconds
Battery Cell :5-18NC/2-6Lipo
Weight :44g
BEC Output :5.5V/4A
Switching Frequency: 8kHz/16kHz
Size :23MM(W)*52MM(L)*14MM(H)
Features:
Extremely low internal resistance
Super smooth and accurate throttle linearity
Safety thermal over-load protection
Auto throttle shut down in signal lose situation
Supports high RPM motors
Power arming protection (prevents the motor from accidentally running when switched ON)
New Advanced programming software
Programmable Features:
1. Brake: ON/OFF
2. Battery type: LiPo or NiCad/NiMh
3. Low Voltage Protection Threshold (Cutoff Threshold)
4. Restore factory setup defaults
5. Timing Setup: Automatic/Low/High
6. Soft Acceleration Start ups: Very Soft / Soft Acceleration / Start Acceleration
7. Active RPM Control (Heli Governor mode)
8. Motor Rotation: Forward / Reverse
9. Switching Frequency: 8kHz/16kHz
10. Low Voltage Cutoff Type: Reduce Power / Hard cutoff |
$58.99
|
ZTW 85A Brushless Speed Controller SBEC 5.5V/5A
* ZTW ESCs may require throttle calibration to be setup before use. Please see page 6 and 7 in the included user manual for instructions on "Powering up the ESC for the first time and setting the automatic throttle calibration."
Specifications:
Output :Continuous Current 85A ,Burst Current 100A for 10 seconds
Battery Cell :5-18NC/2-6Lipo
Weight :60g
BEC Output :5.5V/5A
Switching Frequency: 8kHz/16kHz
Size :23*52*14mm(L*W*H)
Features:
Extremely low internal resistance
Super smooth and accurate throttle linearity
Safety thermal over-load protection
Auto throttle shut down in signal lose situation
Supports high RPM motors
Power arming protection (prevents the motor from accidentally running when switched ON)
New Advanced programming software
Programmable Features:
1. Brake: ON/OFF
2. Battery type: LiPo or NiCad/NiMh
3. Low Voltage Protection Threshold (Cutoff Threshold)
4. Restore factory setup defaults
5. Timing Setup: Automatic/Low/High
6. Soft Acceleration Start ups: Very Soft / Soft Acceleration / Start Acceleration
7. Active RPM Control (Heli Governor mode)
8. Motor Rotation: Forward / Reverse
9. Switching Frequency: 8kHz/16kHz
10. Low Voltage Cutoff Type: Reduce Power / Hard cutoff |
$8.99
|
ZTW 3A Switch mode UBEC
Specifications:
Switch Mode
Output : 5V/3A or 6V/3A switchable (Changeable with a blue jumper)
Input : 6V-25V (2-6S Lipo, 5-18S NiMh/NiCd)
Output Current : Continuous Current 3A, Burst Current 8A
Size : 30mm*9*6mm(L*W*H)
Weight : 7g
Features:
Adopting the USA CPU and decreasing the electromagnetic interference, to be sure that receiver works well .
The working status of UBEC is shown by an indicator (LED). When UBEC works, the blue LED lights.
Battery polarity reversal protection (If the connection is wrong, the UBEC can not work).
|
$14.99
|
ZTW 6A Switch mode UBEC
Specifications:
Switch Mode
Output : 5.0V/6A ,5.5V/6A or 6.0V/6A switchable (Changeable with a blue jumper)
Input : 6V-25V (2-6S Lipo, 5-18S NiMh/NiCd)
Output Current : Continuous Current 6A, Burst Current 10A
Size : 45mm*23*10mm(L*W*H)
Weight : 18g
Features:
Adopting the USA CPU and decreasing the electromagnetic interference, to be sure that receiver works well .
The working status of UBEC is shown by an indicator (LED). When UBEC works, the blue LED lights.
Battery polarity reversal protection (If the connection is wrong, the UBEC can not work).
|
|
|
